Put the welding process, material, and type of work near the top of your resume. Then show what you did before, during, and after welding. This sample follows a production welder who fits and MIG welds mild-steel frames and brackets for packaging equipment.
Carmen Vega, her employers, her school, and the resume below are fictional. Both jobs in the sample are paid shop roles in Rockford, Illinois. Use your own job titles and describe the work you can discuss in an interview.
Carmen Vega
Welder | Mild-Steel MIG Fabrication
(815) 555-0186carmen.vega@example.comRockford, IL
Summary
Production welder who fits and MIG welds mild-steel frames and brackets for packaging equipment. Reads shop drawings and weld symbols, checks fit-up and finished welds, and records work held for quality review.
Experience
- Fit and tack mild-steel tube frames in shop fixtures. Measure both diagonals before and after tacking to check squareness. Hold frames outside the drawing tolerance for the shop lead to review before finish welding.
- Read shop drawings and weld symbols to confirm fillet weld locations and sizes on frames and mounting brackets. Make flat and horizontal fillet welds using MIG welding (GMAW) and follow the shop's approved work instructions. (note 1)
- Look for visible defects in completed welds and verify fillet weld size with a gauge. Tag assemblies with visible porosity and note the affected joint on the job traveler for quality review.
- Compare the drawing revision on the job traveler with the print at the weld station. Hold jobs with a revision mismatch until the shop lead confirms which drawing to use.
- Cut mild-steel tube to length on a band saw, deburred the ends, and labeled pieces by part number before staging them for fit-up.
- Loaded precut pieces into fixtures and checked their orientation with the welder before tacking began.
Education
Skills
MIG welding (GMAW), Mild-steel fit-up and tacking, Shop drawings and weld symbols, Visual weld checks, Fillet weld gauges, Job traveler documentation, Band saw cutting
- Note 1:
The bullet ties MIG to flat and horizontal fillet welds on specific assemblies.
- Note 2:
The school certificate appears under Education. Carmen's resume has no professional certification entry.
Show who did the fit-up
Two welders can run the same process and have different responsibilities. One might weld assemblies that arrive tacked. Another might position the pieces in a fixture and check alignment before welding. Carmen's current job includes fitting and tacking the tube frames. Her helper entry shows how she prepared parts and checked their orientation with the welder.
Experience
- Fit and tack mild-steel tube frames in shop fixtures. Measure both diagonals before and after tacking to check squareness. Hold frames outside the drawing tolerance for the shop lead to review before finish welding. (note 1)
- Loaded precut pieces into fixtures and checked their orientation with the welder before tacking began.
- Note 1:
The diagonal check tells the reader what Carmen measures before the frame goes to finish welding.
If you weld parts prepared by someone else, name the assembly, process, and welds you complete. If you also do the fit-up, describe one feature you check and when you check it. Carmen names the squareness check that can put a frame on hold before finish welding. Include a tolerance only if you can verify it for that assembly.
Name the weld check and who reviews the exception
Carmen checks for visible defects and uses a fillet weld gauge to check size. When she finds visible porosity, she tags the assembly and records the affected joint for quality review. The tag marks the assembly for review, and the job traveler tells the reviewer which joint to look at.
Experience
- Look for visible defects in completed welds and verify fillet weld size with a gauge. Tag assemblies with visible porosity and note the affected joint on the job traveler for quality review. (note 1)
- Note 1:
Carmen identifies the joint for review. The sample supports visual weld checks as a skill and leaves final acceptance with the quality team.
If you lack a verified pass rate or rework figure, describe a check you actually made, what prompted you to hold the part, and who handled the next decision. If you only checked welds at your own station, describe the check that way. The quality control inspector example shows what a separate inspection role can involve.
List training, credentials, and weld tests accurately
Carmen lists her Welding Technology certificate under Education. If your experience comes from a school lab, identify it as coursework or a training project. You can describe the joint you made and how it was checked under supervision.
If you hold a current Certified Welder credential from the American Welding Society (AWS), use the exact credential name and the scope shown on your qualification record. Check the process, material, position, and applicable code before listing them. An employer may also ask for its own practical weld test. Describe a previous shop test as an employer test and include only details you can verify. The certification guide covers how to list earned credentials.
Match the evidence to the shop
For a production MIG opening, Carmen can lead with the flat and horizontal fillet welds and follow with the check she makes on finished work. For a job that includes fitting parts from drawings, she can lead with the tube-frame fit-up and diagonal measurements. Her example covers mild steel. An opening that calls for TIG on stainless steel, pipe welding, or a specific qualification needs its own evidence.
If you are moving from a helper role, keep that title and describe the parts you cut, deburred, staged, or loaded into fixtures. A strong work bullet can show how you prepared material for the welder even if you did not make the finished weld.